[How is it used?
D Tracker, used on FTR223.
Mainly used to protect the front brakes master and clutch lever in the event of a fall during circuit driving and motard racing.
D Tracker allows you to set the Quantity for practice runs and for race outfits.:2 SetThey were using different methods. (For practice runs, I use the one that has been torn to shreds from falling over a lot. It's a waste of money to change to a new one, so I keep using the battered one for practice).
The handlebar was attached to a Renthal, ZETA φ22.2.
Was the one you received as per Image?
Anodized color as per image (Black) The Bent was just as I had imagined it would be. The body is also made of a solid aluminum bar, and I don't think it would break even if it fell over. The body is also made of solid aluminum bars, and I was impressed by the ruggedness.
Was the installation difficult?
However, if you have changed the front brakes master to a radio pon, you will need to use the longer mounting bracket (sold separately) or add a washer and collar to the bracket as shown in the photo. It is also necessary to add a washer and collar to the supplied bracket as shown in the photo so that the body does not interfere with the MASTER.
I also changed the routing of the body to prevent it from interfering with the wire and wiring when it falls, and tightened the bolt on the bracket to prevent it from rotating.
How was your experience with it?
I've used it for about 5 or 6 years, and I've fallen many times on both Asphalt and dirt, but the body never broke, and the front brakes master never broke, the clutch lever never broke, and the wire never tore. In addition, the body was not bent if the fall was only SlipDown.
I've never crashed on the high side before, including the time I was competing in the race, so I can't review whether I'm safe or not after being hit on the high side.
In addition, even if the surface was scraped off by a fall, it would not get stuck even if it fell over next time if the surface was made smooth with File or Glineda.
In order to prevent injuries, it is recommended that the surface of the board be sanded down after a fall.
[Included Parts:were they on?
Bracket, Anchor, Bolt, etc.
[Was there anything that disappointed you?
Anodized (Black) The color faded rather easily and became brownish. I was disappointed in that.
[ITEMS TO BUY TOGETHER
Hand Protector for ArmourGuard
You should buy one to protect your hands from stepping stones.
However, there is an aspect of aerodynamic drag in the Motard race.
If I fall and scrape it off, I'd better buy this one again, but it doesn't break easily, so I can just use it. LOL!
Color, Washer, Long Bolt
If you are installing a Radipon, you need to buy the long Bracket (sold separately) if you don't want to skimp on it, otherwise it will be impossible to install.
92,657.16 ~ ARS (10,814 JPY) 116,528.34 ARS Save 20%
información de entrega
-
Please select product form first.
Product detail
Para las barras de diámetro estándar (22,2 mm)
conjunto izquierda-derecha
adjunto : Kit de montaje medio, adaptador de extremo de barra
**Al quitar la pegatina, hay un agujero de perno para la instalación del protector de manos.
*El adaptador del extremo de la barra es compatible con el diámetro interior del manillar de 13,5 mm a 19 mm..
* La imagen es solo como referencia. La imagen mostrada puede diferir del producto real.
Protectores de manos hechos de una aleación de aluminio rígido, uno de los favoritos de los mejores pilotos de motard y enduro..
Evitar los problemas relacionados con el funcionamiento, como los daños en las palancas debido a las caídas.
Los extremos curvos del manubrio le permiten concentrarse en la conducción sin interferir con el movimiento de los brazos..
Se puede equipar con protectores de manos (se venden por separado).
Kit de montaje con adaptador de medio y extremo de barra.
Precaución
* If there may be an instruction manual included, it will be written in Japanese.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
Opiniones de los usuarios
Reviews with image
Feb 2, 2022
Dec 13, 2020
I used to have the AdventureGuard, but it didn't fit well and I switched to this one. I like the design of this one better.
View Detail
Dec 13, 2020
I was wearing the AdventureHand guard, but I couldn't get the mounting position right, and the guard position was pretty much down ….
I replaced it with an Armor Handguard.
I have bought the Knuckle guard, but I am troubled because I need to remove the ZETASeal to install it.
It's a good looking product and my favorite.
Sep 6, 2020
I like the leeSale price at a good standard and leeSale price...
I use it when I race in the Enduro race with my CRF150R?
The look is as expected of ZETA. Parenthesis with good texture and well mounted Bolt is all Material:It's stainless steel and glistening.
This is a universal product, so it can be installed in combination with CX Handlebar. But it is not possible to insert the bolt into the Handlebar straightly. There are few restrictions on the angle of installation, so if it is within the range of normal use, it can be used. It is written in the Instruction Manual, but there is an order in the tightening of the Bolt. (∩´∀Translated.) ∩
So far, JNCC's COMP, CGCHardEnduro's 5-hour endurance (solo entry) The Lever and Hand Guard works very well as a protection for your motorcycle and your body, even if you hit a standing tree or fall. It has a large radius on the outside so that it can be slippery even if it hits a standing tree. Tell me. Sometimes you can get it.
It is removed when running the Motocross course, but repeated attachments and removals are not a problem.
Large It's not easy to say in a quiet voice, but it's a product of a well-known institution, and it's so durable that it's sold at a high price in NetOaktion and other places, even if it's scratched when you don't need it anymore.
Jun 30, 2020
I hit a standstill and a standing tree on a forest road, but Lever didn't break.
The Hand guard was pointing upwards, but when I hit it, it went back to where it came from.
I'm glad I had it on. If it wasn't, Lever would have broken off and there would have been nothing I could do about it.
New Custom Articles
